發泡膠生產廠家，聚氨酯泡沫填縫劑生產廠家，發泡劑生產廠家

使用范圍：                                                     

門，窗框的填充及安裝；裂縫和缺洞的填充。防塵、防害蟲，防空氣濾滲的密封；空調、排風扇的漏洞填縫；管道和下水道的密封；隔熱、隔音；電器開關盒的安裝定位及絕緣；浴缸，電線出口  裂縫的填充；各種非標易碎物品的防震包裝；屋頂裂縫的填補；防水與保溫；堵各種害蟲唾咬之功能；    堵防老鼠進入管道，孔洞等

APPLICATION AREA:

gate,window frame packing and installment;crack and lack hole packing;dustproof,against harmful insect,against air infiltration's seal;air conditioning,platoon wind the fan's crack sealing;pipeline and sewer's sea;heat insulation,the sound-insulated;electric appliance switch-box's installment locates and insulates;the bathtub electric wire exports the crack packing;each kind of non-sign brittle goods quakeproof packing;roof the crack fill;waterpoofing and heat preservation;stops up each kind of harmful insect saliva to nip function;to stop up against mouse access duct,hole and so on

產品特性：

施工溫度；料罐：+10℃- +30℃

環境：+5℃- +30℃    發泡倍數：78倍

最佳施工溫度：18℃to+25℃

固化后耐溫范圍：-40℃to+90℃

表干時間：10-14分鐘；可切割時間：30-40分鐘

此數據為實驗室條件下測試所得23℃。50%相對濕度

貯存：

未開封時請把本產品保存在+10℃到+30℃的干燥場所，禁止靠近明火或者與易燃易爆物品接觸

CHARACTERISTIC OF PRODUCTS

feed tank：+10℃-+30℃

Environment：+5℃-+30℃foam multiples：78times.

the best construction temperature：18℃to +25℃.

Curing temperature range：-40℃to +90℃.Dry Time 10 to

14 minutes Cutting Time 30-40 minutes This test data

obtained under laboratory conditions 23℃.50%RH

STORAGE

Please put this product without Kaifeng preserved in the +10℃

to + 30℃dry places. Prohibited near open flame or and

inflammable and explosive materials contact.

使用方法：

1.施工前，去除施工表面的浮灰、油污、并在施工表面噴少許水.

2.將料罐上下?lián)u勻幾次，將料罐倒置并旋轉固定于噴槍連接口.

3.使用時將料罐倒置，由下而上地噴出泡沫，一般情況只需填滿接縫的70-90%（泡沫將略微膨脹裝）

4.十分鐘后表面開始固化，靜待約40分鐘即可去除泡沫多余部分

5.本產品不抗紫外線，因此推薦在固化的泡沫表面用其他材料的涂裝，例如：水泥砂漿、涂料等（施工后24小時才可涂裝）

PRODUCTS APPLICATION

1.pre-construction,construction of the surface to remove floating dust,oil.andspray a little water in the surface construction.

2.cans will be expected to shake up and down several times.Material can be fixed on the gun upside down and rotate the connector.

3.material can be used upside down.Spray foam from the buttom up,in general,only 70-90% filled joints（slightly inflated the bubble will install）

4.Ten minutes after the start curing the suface,wait about 40minutes to remove excess foam.

5.This product in not UV,it is recommended in the curing of the foam surface coating with other materials,such as:cement,mortal,paint,etc.（24 hours to paint the construction）.

安全建議：

產品固化后對人體沒有危害。施工請穿戴防護手套、衣服、口罩和護目鏡。施工現場必須具備通風條件。本產品可能引起眼睛，呼吸系統，皮膚不適。不慎吸入后或觸及皮膚會引起刺激癥狀。禁止靠近明火或與易燃易爆物品接觸，禁止吸煙。請勿吸入揮發氣體。萬一吞下請立即送院就醫。不慎吸入后有刺激癥狀時應立即轉移到新鮮空氣處并就醫。避免陽光直射，置于陰涼干燥處，且溫度不超過50℃。使用后禁止燃燒或刺穿空罐。請將涂料放在兒童觸及不到的地方。

Safety recommendations:

The product after curing, no harm to the human body. Construction please wear protective gloves, clothing,masks and goggles. The construction site must be ventilated. This product may cause eye, respiratory system,skin discomfort. Accidentally inhalation or skin contact may cause irritation symptoms. Prohibit near open flame or contact with flammable and explosive articles, no smoking. Do not inhale vapors. If swallowed immediately sent to hospital. The inadvertent inhalation after stimulation symptoms should be immediately transferred to the fresh air and see the doctor. Avoid direct sunlight, in a cool and dry place, and the temperature does not exceed 50℃. After the use of prohibited burning or piercing empty cans. Please put paint on the place where children can not reach